|
|
| Zeile 1: |
Zeile 1: |
| __NOTOC__
| | Terminator franchise is what got me interested in the movies in the first place. The first was a suspenseful cyberpunk thriller, and the second became my favorite movie of all time. The third fell short of intelligence but still solid nonetheless, and the TV series was a good addition to the franchise. Nearing the end of May, the fourth and latest film addition of the beloved sci-fi franchise will open, and viewers are in for a sheer summer spectacle. |
| | |
| [[Bild:LaborBoard1.jpg|300px|right]]
| |
| | |
| ==The Laborboard==
| |
| The Laborboard is a small board for those of you who want to start programming microcontrollers.
| |
| | |
| ==What does it consist of?==
| |
| The board's core is a ATmega32 controller. There are 4 buttons (Port B) and 8 LEDs (Port C) connected. Additionally there is a 16Mhz quartz oscillator, a reset button and a small circuit to stabilize the supply voltage. | |
| | |
| ==Getting started==
| |
| | |
| You can find a list of the needed [[LaborBoardTeile|parts]] in this wiki -- Find the component placement specification and circuit diagram here ''https://www.das-labor.org/trac/browser/microcontroller/doc/Layouts'' . A lot of example code can be found in our [[Subversion]] at ''https://www.das-labor.org/trac/browser/microcontroller''.
| |
| | |
| ==Step by==
| |
| * 06.06.2005, Do: [[Microcontroller Workshop]]
| |
| * 14.06.2005, Fr: [[Microcontroller Workshop Part II]]
| |
| * 15.06.2005, Sa: [[Microcontroller Bastel-Samstag]]
| |
| * 08.07.2005, Fr: [[Microcontroller Workshop Part III]]
| |
| * 06.08.2005, Di: [[Microcontroller Workshop Part V]] (Canbus & Co)
| |
| * 13.09.2005, Di: [[Microcontroller Workshop: Borgs]]
| |
| | |
| * 14.11.2006, Di: [[Microcontroller Workshop]]
| |
| * 16.11.2006, Do: [[Microcontroller Workshop]]
| |
| | |
| ==Projects building upon the Labor Micro Board==
| |
| * [[Blinken Borgs/en]]
| |
| * Peter's [[Shortcut-Tastatur]]
| |
| * [[Automatisierung des Labors|Labor automation projekt]] with the help of [[CAN]] Bus and [[LAP]], the Labor Automation Protocol.
| |
| | |
| * [[Standards zur verdrahtung| wiring standards]]
| |
| | |
| ==Setting fuses==
| |
| For the controllers to work with the external quartz oscillator and to control the LEDs with all pins on Port C, you have to set the fuses correctly. '''ATTENTION: SETTING THE WRONG FUSES CAN BRICK YOUR CONTROLLER!''' The order is important, too: first set hfuse, then lfuse.
| |
| | |
| ...you have been warned. ;)
| |
| | |
| avrdude -c bsd -p m32 -t
| |
| ...some kind of console upens up ...
| |
| write hfuse 0 0xc9
| |
| write lfuse 0 0x9f
| |
| quit
| |
| | |
| ... you should see a confirmation message
| |
| | |
| If you lack avrdude, you can also use uisp:
| |
| | |
| uisp -dprog=bsd --wr_fuse_h=0xc9
| |
| uisp -dprog=bsd --wr_fuse_l=0x9f
| |
| | |
| == pin assignment of the programming plug ==
| |
| +-----+
| |
| GND | 0 0 | MISO
| |
| GND | 0 0 | SCK
| |
| GND | 0 0 RESET (inv)
| |
| GND | 0 0 | (not assigned)
| |
| VCC | 0 0 | MOSI
| |
| +-----+
| |
| ==Links==
| |
| * AVR + gcc tutorial: http://www.mikrocontroller.net/articles/AVR-GCC-Tutorial
| |
| * avr-libc manual: http://www.nongnu.org/avr-libc/user-manual/index.html
| |
| * Toolchain install: http://www.nongnu.org/avr-libc/user-manual/install_tools.html (do not use old port/packages! avr-libc < 1.23 has bugs in malloc)
| |
| * ATmega32 Data Sheet: http://www.atmel.com/dyn/resources/prod_documents/doc2503.pdf
| |
| | |
| [[Category:Microcontroller]]
| |