Laser exposer

Aus LaborWiki
Version vom 8. Mai 2012, 10:17 Uhr von MadEngineer (Diskussion | Beiträge) (→‎Belichten: Ergebnis Belichtung mit Delay 250: einwandfrei)
Wechseln zu: Navigation, Suche
       
Laser exposer

Release status: Stable [box doku]

Description Scanning laser exposer that exposes pcbs for etching
Author(s)  Tixiv
Last Version  V1.0 ()
Platform  AVR (ATmega32/ATmega8)
Download  Software: SVN browse

„Stable“ befindet sich nicht in der Liste (experimental, beta, stable, obsolete, unknown) zulässiger Werte für das Attribut „Pr status“.




Hardware

Materials

Laser Exposer

I made the haware mainly from stuff I had laying around (for the Germans: Edelschrott) but also from some stuff I had to buy specially for this project.

  • flatbed scanner (for the base and vertical transport)
  • polygon mirror and laser assembly from Kyocera F1200 printer (not the FS1200, the F1200 is a very old modell. It belonged to my father in the 90's).
  • 1W 450nm blue Laser diode from ebay (40 Bucks) to replace the infrared one in the printer's assembly.
  • laser housing and glas lens from ebay (15 Bucks)
  • Thermal paste to mount the laser diode
  • Alluminium block to mount and cool the laser housing
  • Powersupply from old external Harddisk 12V/2A
  • Materials and Parts to make the two microcontroller PCBs (20 Bucks, some junked Parts reused)
  • Wood to make the Case

How it works

Sled
Sled


The polygon mirror assembly is mounted vertically on the flatbed scanners sled. The flatbed scanner sled is the Vertical axis, and the polygon mirror defelcting the laser in the scanner is the horizonbtal axis. Each Horizontal line is scanned about 150 times before the sled moves on to the next vertical position. The laser is scanned by the mirror continuasly at 55 Revolutions of the mirror per second, or 333 Hz scanrate, as the mirror is hexagon shaped. The exposure pattern is produced by turning the laser on and of synced to the rotation of the mirror.

There are two microcontroller boards used. One is a digital servo speed controller for the polygon mirror motor. It just runs the motor up to the exact speed when requested, and sends a servo locked signal while the motor is at the correct speed.

The other Board is the main board, which has the current source to control the Laser, and a driver for the stepper motor. This Board is connected to the PC through an uart. The PC instructs the machine waht to do. The PC can tell the main board to start the scanner and run the stpper to a specific position, and transfer data for scanlines, one line at a time. Each scan line is scanned about half a second, and then the PC tells the stepper to move on one position, and sends the data for the next scanline. During the half second, the line is exposed about 150 times.

Optics

The original laser in a laserprinter is infrared, and that wavelength doesn't work for exposing pcbs. I removed the infrared laser, and mad-engineer helped me to make a nice alluminium laser mount, and mill down the mirror assembly to fit it. As the lenses in the polygon mirror assembly had the wrong optical properties for my application (different wavelength and different focussing distance), I removed them all. The optical system now consists only of the laser, its focussing lens, and the polygon mirror. There is one problem with this: as the beam length varies with the angle of the deflected laser beam, the focus of the laser lens would also have to be adjusted for each beam length. As this isn't done, the laser gets blurry at the ends and the middle of the scanline. But this is not a problem in practice, as the image gets sharp enough.

Electronics

Main Board

component layout

Datei:Exposer schematic.pdf

Datei:Exposer layout.pdf

The polygon mirror motor servo board
The main board, the stepper motor, and the opto to detect its 0 position

The main board controls the laser and the stepper motor. It has an atmega32 microcontroller as brain. The laser is driven by a current source made from transistors, and the stepper motor of the flat bed scanner is driven by an uln2803. it runs on a 12V power supply, and makes 5V for the microcontroller with a 7805.

Motor Controller Board

Datei:Scanner head schamatic.pdf

The motor controller has an attiny2313 microcontroller, and it's own 78L05 to make a stable 5V supply (using the one from the cable would leed instability, as the GND current varies in the cable because of the motor). I reverse engineered the interace to the polygon mirror motor. It has 12V powersupply, a speed control pin, which accepts a strange range of voltages, and a symterical frequency generator output (FG). This output is a zig zag shaped induction loop around the motor, which generates a feedback frequency of how fast the motor is going. This is fed to the AVR's analog comparator. The microcontroller locks this signal to a reference frequency of 2kHz, which yields 55.555555555555... rotations of the motor per second, and 333.333333...Hz scanrate.


HowTo

Achtung: Schlitten nicht per Hand verfahren!

Layout exportieren

  • Zu druckende Layer auswählen mit Dimension
  • drill-aid.ulp ausführen
  • Datei --> Drucken
    • Drucker: In Datei (PDF)
    • Optionen
      • Spiegeln, wenn Buttom-Layer geätzt werden soll
      • Drehen, so dass das Layout aufrecht steht (Höhe > Breite)
      • Schwarz
      • Gefüllt
      • Bildüberschrift: Nicht ausgewählt! (Wichtig, da das Programm das umgebende Rechteck auswertet)
    • Skalierungsfaktor 1

Belichten

  • Gerät einschalten
  • Software starten am besten die Python-Variante pyExposerControl
  • File --> Open: Vorher erstellte PDF öffnen
  • Rotation: Drehen des Layout in Grad (gegen den Uhrzeigersinn)
  • Upper / Right margin: Abstand zwischen Layout und Rändern einstellen
  • Nutzen erstellen
    • X/Y Copys: Anzahl der Kopien in die jeweilige Richtung
    • X/Y spacing: Abstand zwischen den einzelnen Kopien
  • Einstellungen müssen mit Apply übernommen werden.
  • Die Größe der Platine unter size überprüfen
  • Delay einstellen
    • 500 mit Bungard-Basismaterial: Überbelichtet
    • 300 mit Bungard-Basismaterial: Gut belichtet, jedoch auf werden die Freiflächen etwas angeätzt. (Vielleicht ist der Standby-Strahl zu stark). Vielleicht könnte man schneller belichten.
    • 250 mit Bungard-Basismaterial: Ergebnis ist einwandfrei
  • Platine an den Anschlag hinten rechts anlegen.
  • Deckel schließen
  • GO klicken
  • Belichtung läuft
    • Wird die Klappe geöffnet, stoppt die Belichtung und wird nach schließen fortgesetzt. Achtung Platine könnte sich durch Erschütterung verschieben beim Öffnen.
    • Der bereits belichtete Bereich wird in der Software rot dargestellt. (Nur in den weißen Bereichen sichtbar)