Laborboard/en: Unterschied zwischen den Versionen

Aktuelle Version vom 23. Juni 2011, 11:33 Uhr

The Laborboard[Bearbeiten | Quelltext bearbeiten]

The Laborboard is a small board for those of you who want to start programming microcontrollers.

What does it consist of?[Bearbeiten | Quelltext bearbeiten]

The board's core is a ATmega32 controller. There are 4 buttons (Port B) and 8 LEDs (Port C) connected. Additionally there is a 16Mhz quartz oscillator, a reset button and a small circuit to stabilize the supply voltage.

Getting started[Bearbeiten | Quelltext bearbeiten]

You can find a list of the needed parts in this wiki -- Find the component placement specification and circuit diagram here https://www.das-labor.org/trac/browser/microcontroller/doc/Layouts . A lot of example code can be found in our Subversion at https://www.das-labor.org/trac/browser/microcontroller.

Step by[Bearbeiten | Quelltext bearbeiten]

06.06.2005, Do: Microcontroller Workshop
14.06.2005, Fr: Microcontroller Workshop Part II
15.06.2005, Sa: Microcontroller Bastel-Samstag
08.07.2005, Fr: Microcontroller Workshop Part III
06.08.2005, Di: Microcontroller Workshop Part V (Canbus & Co)
13.09.2005, Di: Microcontroller Workshop: Borgs

14.11.2006, Di: Microcontroller Workshop
16.11.2006, Do: Microcontroller Workshop

Projects building upon the Labor Micro Board[Bearbeiten | Quelltext bearbeiten]

Blinken Borgs/en
Peter's Shortcut-Tastatur
Labor automation projekt with the help of CAN Bus and LAP, the Labor Automation Protocol.

Setting fuses[Bearbeiten | Quelltext bearbeiten]

For the controllers to work with the external quartz oscillator and to control the LEDs with all pins on Port C, you have to set the fuses correctly. ATTENTION: SETTING THE WRONG FUSES CAN BRICK YOUR CONTROLLER! The order is important, too: first set hfuse, then lfuse.

...you have been warned. ;)

 avrdude -c bsd -p m32 -t

...some kind of console upens up ...

 write hfuse 0 0xc9
 write lfuse 0 0x9f
 quit

... you should see a confirmation message

If you lack avrdude, you can also use uisp:

 uisp -dprog=bsd --wr_fuse_h=0xc9
 uisp -dprog=bsd --wr_fuse_l=0x9f

pin assignment of the programming plug[Bearbeiten | Quelltext bearbeiten]

       +-----+
   GND | 0 0 | MISO
   GND | 0 0 | SCK
   GND | 0 0   RESET (inv)
   GND | 0 0 | (not assigned)
   VCC | 0 0 | MOSI
       +-----+

Links[Bearbeiten | Quelltext bearbeiten]

AVR + gcc tutorial: http://www.mikrocontroller.net/articles/AVR-GCC-Tutorial
avr-libc manual: http://www.nongnu.org/avr-libc/user-manual/index.html
Toolchain install: http://www.nongnu.org/avr-libc/user-manual/install_tools.html (do not use old port/packages! avr-libc < 1.23 has bugs in malloc)
ATmega32 Data Sheet: http://www.atmel.com/dyn/resources/prod_documents/doc2503.pdf

@@ Zeile 4: / Zeile 4: @@
 ==The Laborboard==
-The Laborboard is a small board you can gain experience in microcontrollers with.
+The Laborboard is a small board for those of you who want to start programming microcontrollers.
 ==What does it consist of?==
-The board's core is a ATmega32 controller. There are 4 buttons (Port B) and 8 LEDs (Port C) connected. Additionally there is a 16Mhz quartz oscillator, a reset button and a small circuit to stabilize the supply voltage.r, und eine kleine Schaltung zum stabilisieren der Versorgungsspannung.
+The board's core is a ATmega32 controller. There are 4 buttons (Port B) and 8 LEDs (Port C) connected. Additionally there is a 16Mhz quartz oscillator, a reset button and a small circuit to stabilize the supply voltage.
 ==Getting started==
-You can find a list of the needed [[LaborBoardTeile|parts]] in this wiki -- Find the component placement specification and circuit diagram here ''https://roulette.das-labor.org/svnview/microcontroller/doc/Layouts/'' . A lot of example code can be found in our [[Subversion]] at ''https://roulette.das-labor.org/svnview/microcontroller''.
+You can find a list of the needed [[LaborBoardTeile|parts]] in this wiki -- Find the component placement specification and circuit diagram here ''https://www.das-labor.org/trac/browser/microcontroller/doc/Layouts'' . A lot of example code can be found in our [[Subversion]] at ''https://www.das-labor.org/trac/browser/microcontroller''.
 ==Step by==
@@ Zeile 29: / Zeile 29: @@
 * [[Automatisierung des Labors|Labor automation projekt]] with the help of [[CAN]] Bus and  [[LAP]], the Labor Automation Protocol.
-* [[Standards zur verdrahtung| wiring standards]]
 ==Setting fuses==
-For the controllers to work with the external quartz oscillator and to control the LEDs with all pins on Port C, you have to set the fuses correctly. '''ATTENTION: SETTING THE WRONG FUSES CAN BRICK YOUR CONTOLLER!''' The order is important, too: first set hfuse, then lfuse.
+For the controllers to work with the external quartz oscillator and to control the LEDs with all pins on Port C, you have to set the fuses correctly. '''ATTENTION: SETTING THE WRONG FUSES CAN BRICK YOUR CONTROLLER!''' The order is important, too: first set hfuse, then lfuse.
 ...you have been warned. ;)