Labnode/phasecut: Unterschied zwischen den Versionen

Aus LaborWiki
Wechseln zu: Navigation, Suche
(hints...)
Keine Bearbeitungszusammenfassung
 
(4 dazwischenliegende Versionen von 3 Benutzern werden nicht angezeigt)
Zeile 1: Zeile 1:
{{ProjektInfoBox
{{ProjektInfoBox
|name        = phasecut
|name        = phasecut
|status      = Stable
|status      = obsolete
|image      = phasecut_vorlage.png
|image      = phasecut_vorlage.png
|description = 4 galvanisch getrennte Triac Ausgänge
|description = 4 galvanisch getrennte Triac Ausgänge
Zeile 44: Zeile 44:
'''TODO:'''
'''TODO:'''
* replace MOC3020 with MOC3023
* replace MOC3020 with MOC3023
* add RC snubber to limit dU/dt !
* add choke to limit dI/dt !
* oder man nimmt einen snubberless triac z.B. BTB 08/600BW


'''Hints'''
'''Hints'''
Zeile 50: Zeile 53:


[[Datei:phasecut_vorlage.png|thumb|260px|right|Platine]]
[[Datei:phasecut_vorlage.png|thumb|260px|right|Platine]]
{{Navigationsleiste_Automatisierung}}

Aktuelle Version vom 23. Februar 2018, 20:42 Uhr

         
phasecut

Release status: obsolete [box doku]

Phasecut vorlage.png
Description 4 galvanisch getrennte Triac Ausgänge
Author(s)  Tixiv pl4nkton
Last Version  V1.1 ()
Platform  labnode extension
Download  Software: SVN browse




In Aufputzdose verbaut
Schaltplan
Platine

Platine mit 4 galvanisch getrennten Triac Ausgängen für Phasenanschnitt (z.B. für Glühlampen, Halogenlampen mit Transformator (keine elektronischen)). Eingang für Nulldurchgangserkennung. Muss an EXT 2 angeschlossen werden (ICP PIN).

Auf dem labnode läuft der SVN:can_dimmer.

CAN:

function 0x00 - 0x04
lamp 0x00 - 0x03
brightness 0x00 - 0xff
  • destination port:1
    • 1st data byte is the function (0x00-0x04)
      • function 0x00:
        • toggle lamps, switch to next pattern, called by the light button in the room
      • function 0x01:
        • set lamp (2nd data byte) brightness to value (3rd data byte)
      • function 0x02:
        • fade all lamps, called by the light button in the room if held
      • function 0x03:
        • toggle direction for fading, called by the light button in the room if held and then released
      • function 0x04:
        • enable/disable (3rd data byte), disable == 0 brightness, enable == [saved brightness (function 0x01)] lamp (2nd data byte)

TODO:

  • replace MOC3020 with MOC3023
  • add RC snubber to limit dU/dt !
  • add choke to limit dI/dt !
  • oder man nimmt einen snubberless triac z.B. BTB 08/600BW

Hints

  • The resistor in front of the LEDs might be changed according to voltage of the LEDs - watch out: LEDs current has to match the current of the optotriac
  • optotriacs with zero crossing detector are NOT suitable for dimming ;)
Platine