Benutzer:Hansinator: Unterschied zwischen den Versionen

Aus LaborWiki
Wechseln zu: Navigation, Suche
KKeine Bearbeitungszusammenfassung
KKeine Bearbeitungszusammenfassung
Zeile 13: Zeile 13:
[http://web.archive.org/web/20030201183139/mpt.phrasewise.com/discuss/msgReader$173 Why Free Software usability tends to suck]
[http://web.archive.org/web/20030201183139/mpt.phrasewise.com/discuss/msgReader$173 Why Free Software usability tends to suck]
<br />
<br />
== Brainstorming ==
* [[HAP Version 0]]<br />Ein Protokoll zur Hausautomatisierung


== Mein(e) Robo(s) ==
== Mein(e) Robo(s) ==
Zeile 20: Zeile 25:
Vielen Dank an [[Benutzer:Mati|Mati]] für das Foto!<br style="clear:both" />
Vielen Dank an [[Benutzer:Mati|Mati]] für das Foto!<br style="clear:both" />


== Grüße ==
Jetzt möchte ich noch einige zufällig sortierte, nette Leute grüßen! :D
DU fehlst hier, glaubst aber, ich würde dich auch grüßen wollen, hätte ich dich nicht vergessen
Trag dich halt selber ein...
'''Menschen mit nicht vorhandenen Benutzerseiten werden nicht verlinkt.'''
* [[Benutzer:Mati|Mati]]
* [[Benutzer:Ansgar|Ansgar]]
* [[Benutzer:Bg|Daniel]]
* [[Benutzer:Fabian|Fabian]]
* [[Benutzer:Jiffies|Jiffies]]
* [[Benutzer:Martin|Martin]]
* [[Benutzer:Soeren|Soeren]]
* [[Benutzer:Suschman|Suschmam]]
* [[Benutzer:TiL|Til]]
* [[Benutzer:Thomas|Thomas]]
* [[Benutzer:Theodor|Joerg]]
* [[Benutzer:Kruemel|Kruemel]]
<br>


== Kunst im Lab ==
== Kunst im Lab ==

Version vom 2. September 2009, 13:09 Uhr

Hallo, Willkommen auf meiner Seite!


Was ich so mache:

  • Ich bastele momentan an Robotern, siehe unten
  • Ich programmiere manchmal Animationen für die Borgs
  • Alle farbigen Borgs haben Plasmaeffekte von mir :-)
  • Ich habe an der rfm12lib, dem rfm12usb und dem rfm12 Bootloader mitgebastelt.. ausserdem benutze ich rfm12s in meinen Projekten
  • Ich bringe Design in das Wiki!
  • Ich habe schon mal ein Kind gelötet...


Why Free Software usability tends to suck


Brainstorming


Mein(e) Robo(s)

Hansis Roboter

Rechts sieht man mein aktuelles Roboterprojekt, den Shr0dBot.

Vielen Dank an Mati für das Foto!


Kunst im Lab

Das habe ich mal gemalt, als ich die bunte Kreide fand.

Tafel


VacuBot

==== MOTORCTRL ATMEGA8 PIN CONFIGURATION ====

Names in () are or were planned.
Pins marked with [in] are inputs, whilst the ones marked with [out] are outputs.
All other pins make use of their respective special function(s).


** GENERIC
XTAL1,2	- 16MHZ, no capacitors
VCC,
AVCC,
AREF	- +5V 7805, 100nF
GND	- COMMON GROUND


** PORT B
0 - VACCUUM CLEANER DRIVE ON/OFF [out]
1 - PWM MOTOR 1 [OC1A]
2 - ISP [SPI SS], PWM MOTOR 2 [OC1B]
3 - ISP [SPI MOSI], WHEEL/MOTOR 1 LIFTOFF DETECTOR [in]
4 - ISP [SPI MISO], WHEEL/MOTOR 2 LIFTOFF DETECTOR [in]
5 - ISP [SPI SCK], FRONT LIFTOFF DETECTOR [in]
6 - XTAL1
7 - XTAL2

** PORT C
0 - BATTERY POWER DIVIDER (1nF load) [ADC0]
1 - MOTOR 1 CURRENT MEASUREMENT (capacitive load?) [ADC1]
2 - MOTOR 2 CURRENT MEASUREMENT (capacitive load?) [ADC2]
3 - ACCU LOADER ON/OFF [out]
4 - SPI SLAVE [SDA]
5 - SPI SLAVE [SCL]
6 - RESET, PRELIMINARY (COULD BE BRUSH DRIVE ON/OFF [out])


** PORT D
0 - MOTOR 2 FORWARD [out]
1 - MOTOR 2 REVERSE [out]
2 - ENCODER A [in]
3 - ENCODER B [in]
4 - MOTOR 1 FORWARD [out]
5 - MOTOR 1 REVERSE [out]
6 - BRUSH DRIVE ON/OFF [out]
7 - FREE


** FREE
PD6, PD7


==== MOTORCTRL MISC STUFF ====

* Encoder IR-Diodes 1k ?? (re-evaluate)
* How to connect phototransistors? I can remeber they had 1k resistors on em. (See on orig. board)
* Use 1/8th Voltage divider (14.4 / 8 = 1.6V -> 12 cells * 1.5V max = 18V -> 18/8 = 2,25V)
* Use logic level fets for vacuum and brush motor turnon/off
* Reverse engineer loader circuit, reuse relais if it could cut loader power
* Use L6202 motor driver ICs

==== MAINBOARD SPECS ====

* Use the fat 128k flash / 16k ram 40pin DIP Atmega
* Probably use a switched power supply -> ask peter for that chip
* Think of creative use for the big fat atmel
* Use rfm12