AD9911DDS: Unterschied zwischen den Versionen

Aus LaborWiki
Wechseln zu: Navigation, Suche
K (+results)
 
(2 dazwischenliegende Versionen von 2 Benutzern werden nicht angezeigt)
Zeile 1: Zeile 1:
 
{{ProjektInfoBox
 
{{ProjektInfoBox
|name       = AD9911DDS
+
|name=AD9911DDS
|status     = experimental  
+
|status=experimental
|image       = AD9911_devboard.jpg
+
|image=AD9911_devboard.jpg
|description = Direct Digital Synthesizer
+
|description=Direct Digital Synthesizer
|author      = siro
+
|username=siro
|username    = siro
+
|author=siro
|version     = 0.1<br>
+
|version=0.1<br>
|update     = '''[[Benutzer:Siro|Siro]] 18 Dez. 2013 (CET)'''
+
|update=18 Dez. 2013
 
+
|platform=*
|platform   = *
+
|license=GPL
|license     = GPL
+
|download=https://github.com/siro20/AD9911
|download   =  
+
|tags=Audio,
 
}}
 
}}
 
 
== AD9911DDS ==
 
== AD9911DDS ==
 
This project describes the AD9911 Direct Digital Synthesizer. It is capable of generating a sine-wave between 250Mhz and >1Hz.
 
This project describes the AD9911 Direct Digital Synthesizer. It is capable of generating a sine-wave between 250Mhz and >1Hz.
Zeile 93: Zeile 92:
 
* toogle I/O-Update pin
 
* toogle I/O-Update pin
  
*TODO upload files*
+
https://github.com/siro20/AD9911
 
=== Changes applied to Hardware ===
 
=== Changes applied to Hardware ===
 
* pull PWR_DWN_CTL low
 
* pull PWR_DWN_CTL low

Aktuelle Version vom 7. April 2017, 23:43 Uhr

           
AD9911DDS

Release status: experimental [box doku]

AD9911 devboard.jpg
Description Direct Digital Synthesizer
Author(s)  siro
Last Version  0.1
Platform  *
License  GPL
Download  https://github.com/siro20/AD9911



AD9911DDS[Bearbeiten]

This project describes the AD9911 Direct Digital Synthesizer. It is capable of generating a sine-wave between 250Mhz and >1Hz. The created evaluation unit is descripted here.

The Hardware[Bearbeiten]

  • CLK_MODE_SEL = 1.8V
  • Rset = 1k91
  • crystal 25Mhz
  • DVDD 1.8V
  • AVDD 1.8V
  • DVIO 3.3V
  • SDIO_0 MOSI
  • SDIO_2 MISO
  • PLL 20x, 500MSPS DAC
  • maximum frequency possible 250Mhz
  • maximum frequency recommended 150Mhz
  • low pass required
  • active current 120mA
  • output AC coupled

channels[Bearbeiten]

There are four channels:

  • channel 0: aux channel
  • channel 1: primary channel
  • channel 2: aux channel
  • channel 3: aux channel

channel 1 is connected to the DAC. all aux channels are capable of modulating channel 1.

modes of operation[Bearbeiten]

  • single tone (frequency,amplitude,phase adjustable)
  • 2 tone test mode (amplitude modulated single tone)
  • 2/4/8/16 FSK/ASK/PSK
  • frequency/amplitude/phase ramp up
  • frequency/amplitude/phase ramp down
  • frequency/amplitude/phase sweep

SPI interface[Bearbeiten]

default
2-wire SPI mode, SDIO_0 is bidirectional !

  • SPI write
    • CPOL=0
    • CPHA=0
  • SPI read
    • CPOL=1
    • CPHA=1

3-wire SPI mode

  • configure 3-wire SPI mode using reg 0
  • set msb mode (default) using reg 0
  • SDIO_0 is MOSI
  • SDIO_2 is MISO

MSB/LSB mode

  • MSB
    • the Most Significant Bit is transfered first
    • the Most Significant Byte is transfered first
  • LSB
    • the Least Significant Bit is transfered first
    • the Least Significant Byte is transfered first

register select

  • register 0, 1, 2 are independent
  • channel register 0x03 - 0x18 are written to using the enable bits in register 0
  • you can write to multiple channels at once !


*TODO upload files*

The Software[Bearbeiten]

I've created a simple programm that runs on teensy 2.0 (ATMEGA32U4). It should run on any ATmega, just change the I/O ports.
Timings are not critical, as the ATmega is much slower than the maximum I/O updaterate of the AD9911.
Software flow:

  • write register 0 (channel select bits)
  • write register 1 and 2 (digital power down, pll multiplier)
  • write to selected channel registers 0x03 - 0x18
  • toogle I/O-Update pin

https://github.com/siro20/AD9911

Changes applied to Hardware[Bearbeiten]

  • pull PWR_DWN_CTL low
  • pull SDIO_3 low
  • terminate IDAC with 50 Ohms agains AVCC
  • terminate !IDAC with 50 Ohms agains AVCC
  • include a 5th order low pass filter
  • include a transformer
  • series resistance for SPI interface

Results[Bearbeiten]

Test Results:

  • third order 200Mhz low pass
  • LeCroy Waverunner 1GSPS
  • 5V PowerSupply
  • SingleTone Mode
AD9911 Devboard PCB soldered

Dds 200.png Dds 160.png Dds 100.png Dds 10.png